|
SPECIMEN LABEL UPDATES AVATLABLE ,4T WWR'.CREENBOOK.NET 3
<br />• Nozzle Type-Uee a nozzle type that is designed for the intended application,
<br />With most nozzle types, narrowerspmy anglesproduc<largerdroplers. Consider
<br />using low-drift nozzles. Solid stream noales oriented straight back produce
<br />the largest droplets and the lowest drift.
<br />nom Length: For some use patterns, reducing the effective boom length m less
<br />than 3'. of the wingspan or rotor length may further reduce drift without reducing
<br />swath width.
<br />Application Height: Applications should not 6e made at a height greater than
<br />10 feet above the top of the largest plants unless a greater height is required
<br />for airemft safety. Making applications at the lowest height that is safe reduces
<br />exposure of droplets to evaporation and wind.
<br />Swath Adjustment: When applications are made with a crosswind, the swath
<br />will be displaced downwazd. Therefore, on the up and downwind edges of the
<br />field, the applicator must compensate for this displacement by adjuring ttte path
<br />of the airctafi upwind. Swath adjustment distance should increase, with increasing
<br />drift potential (higher wind, smaller drops, etc.)
<br />Wind: Drift potental is lowest between wind speeds of 2-10 mph. However,
<br />many facmrs, including droplet size and equipment type determine drift potential
<br />at any given speed. Application should be avoided below 2 mph due m variable
<br />wind direction and high inversion potential. NOTE: Local [ertain can influence
<br />wind patterns. Every applicamr should be familiar with local wind panerns and
<br />how thry affect spray drift.
<br />Temperature And Humidity: When making applications in low relative humid-
<br />ity, set up equipmrnt m produce larger droplets m compensate for evaporation,
<br />Droplet evaporation is most seven when conditions am both hot and dry.
<br />Temperahre Inversions: Applications should not newt during a local, low
<br />level temperature inversion because drift potential is high. Tempemmrc inversions
<br />mstrim vettical air mixing, which cattses small suspended droplets to remain in
<br />a concentrated cloud. This cloud can move in unpredictable direMions due m
<br />the light variable winds wmmon during inversions. Tempemmre inversions are
<br />charscteriud by increasing temperatures with altitude and am common on tdghts
<br />with limited cloud Cover and light [o no wind. They begin to form as the sun
<br />sets and often continue into the rooming. Their presence can be indicated by
<br />ground fog; however, if fog is not present inversions can also be identified by
<br />the movement of tht smoke from a ground source or an aircmfr smoke generator.
<br />Smoke that layers and moves laterally in a wncentmted cloud (under loo wind
<br />conditions) indicates an inversion, while smoke that moves upward and rapidly
<br />dissipates indicates goad vertical au mixing.
<br />Sensitive Areas: The pesticide should only be applied when the potential for
<br />drift m adjacent sensitive areas (e.g. residential areas, bodies of water, known
<br />bite[ for threatened or endangered species, non-target crops) is minimal (c.g.
<br />en wind is blowing away from the sensitive arras).
<br />izing DireMioms
<br />Water Dilution-TO prepare a water dilution of Redeem R&P:
<br />1. Add H. of the required spray volume to the spray tank and start agitation.
<br />2. Add the required amount of Redeem R&P.
<br />3. Add any surfactants, rnop oils, or other adjuvants according to manufacturer's
<br />label.
<br />4. Add any spray thickening agent, if needed to control drift, according to the
<br />manufacturer's label.
<br />5. Agitate during final filling of the spray tank and maintain sufficient agitation
<br />during application to ensure uniformity of me spray mizmre.
<br />Note: Allow time for thorough miring of each spray ingredient before adding the
<br />next If allowed to stand after mixing, agitate spray mixture before use.
<br />Application D'mecdons
<br />Application Timing
<br />Appty to actively growing weeds. Extreme growing conditions such as drought or
<br />cold temperatures prior to, at or following application may redact or delay weed
<br />control. Only weeds which ate emerged at die lime of application will be con-
<br />trolled. Wet foliage at the time of application may decrease control. Applications
<br />of this product are min-fas! within 2 hours afar application.
<br />Application Rates
<br />Generally, application rates at the lower end of the recommended rate range will
<br />be satisfactory for young, succulent growth of sensitive weed species, For less
<br />sensttive species, perennials, and under conditions where control is more difficult
<br />(plant stress conditions such as draught or extreme tempemmres, dense weed
<br />smnds and/or larger weeds) the higher rates within the rate range wi0 be needed.
<br />Weeds growing in the absence of gross competition generally require higher rates
<br />m obtain satisfactory control or suppression.
<br />Use of Surfactants
<br />A non-ionic surfactant cleared for use on growing crops at the manufacturer's
<br />recommended rate is recommended for all applications of this product. Use a
<br />higher recommended rate of surfactant in the spiny mizmre wdren applying lower
<br />spray volumes per acre.
<br />Coverage
<br />ply in 3 or more gallons per acx by air or ]0 or more gallons per acre by
<br />and equipment. Use sufficrent spray volume to provide thorough coverage and
<br />uniform spray panem. Inadequate spray volume and coverage may insult in
<br />decreased weed control. As vegetative canopy and weed density increase, spray
<br />volume should be increased to obtain equivalent weed control. Use larger nozzle
<br />tips ar decrease spraying speed m increase spray volume rather than increasing
<br />boom pressure. Refer to manufacturer's recommendations for information on
<br />reladonships between spray volume, and nozzle size and arrangement.
<br />Database ~atid format copyright ©bp C&P Press. All rights reserved.
<br />Spot Application
<br />To prevent misapplication, h is recommended that spot applications be applied
<br />with calibrated equipment or with hand sprayers according m directions provided
<br />below.
<br />Hand-Held Sprayers: Hand-held or backpack sprayers may be used for spot
<br />applicators. Care should be taken m apply the spray uniformly and at a rate
<br />equivalent m a broadcast application. Application rates in the table are based on
<br />an area of 1,000 sq ft. Mite the amount of this product (fl oz or m]) corresponding
<br />m the desired broadcast rate in one or more gallons of spray. To calculate the
<br />amount of product required for larger areas, multiply the Wble value (fl oz or ml)
<br />by the area m be treated in "thousands" of square fee; e.g, if the area m be
<br />treated is 3,500 sq f; multiply the table value by 3.5 (tale. 3,500 - 1,000 = 3.5).
<br />An area of 1000 sq ft is approximately 10.5 x 10.5 yards (strides) in size.
<br />Amoum of Redeem RB:P to Fquzl Specified Broadest Rate
<br />(Mix with I Gallon or More of Water and Apply /0 1,000 aq ft)
<br />7 pUaere 2 pNacre 3 pt/aere 4 ptlaerc
<br />0.3711 az 0,75 Fl oz I.1 Fl oz I.5 Fl oz
<br />(I 1 mI) (22 ml) (33 m0 (44 m0
<br />rl Fl oz = 29.6 (30) ml
<br />Weeds Controlled or Suppressed and Use Rates
<br />General Recommendations
<br />• Use the higher rotes when hard to control sptcies are prevakn; when applica-
<br />tions are made to mature weeds in advanced stages of growth, or during periods
<br />of drought stress or law temperatures.
<br />• Rates in the lower end of the rate range are recommended only where grass
<br />response (wmpetidon) will help tc suppress weed growth following treatment.
<br />• This product is not recommended for control of woody plants, however, sup-
<br />pression or short-term control of certain woody plants such as multiflom rose
<br />and blackberry within treated areas may be observed at application rates rec-
<br />ommended for control of annual and perennial weeds.
<br />• Unless otherwise noted, apply when weeds are actively growing; use lower rate
<br />when weeds art 6 inches or less in height increase rate for larger weeds up m
<br />flowering.
<br />Note: Numbers in paren[hesa refer to footnotes below table
<br /> Applieatioo Rate
<br />Weed Species (pindacre)
<br />burdock peppcrweed, Virginia 1.5-2
<br />dower, red pineeppleweed
<br />clover, white plantain, broadleaf
<br />cocklcbur,wmman planain, narrowlwf(buckhom)
<br />wffaweed ragweed, common
<br />wmflower (bachelor button) ragweed, Western (3)
<br />crown salsify, meadow
<br />dandelion, wmmon shepherdspure
<br />dandelion false (spotted meezeweed, biaer
<br />wtsear) sorrel, red
<br />grouvdsel, wmmon morel, sheep
<br />horseweed wwthinle, annual
<br />jimsonweed smMisrle, yellow (4)
<br />knapweed, diffuse (1) sunflower wmmon
<br />knapwee4 spotted (1) [caul, common
<br />lambsquarters thistle, bull (5)
<br />lewce, Prickly thistle, musk (5)
<br />lowweed thisde, plumeless
<br />marshelder (2) vetch
<br />nightshade wormwood, absinth
<br />oxeye daisy
<br />buttercup, hairy 2-3
<br />dock, curly (6)
<br />amaranth, spiny (pigweed) (7) akelemnweed, rash 2.5~
<br /><hiwry sowthistle, perennial
<br />dogfennel (7) thisde, wavylwf(10)
<br />horsenmle (g) tropical soda apple ('!)
<br />ironweed, Western (9)
<br />ragwort, mnry
<br />hawkweed 3-4
<br />knapwted, Russian (I I)
<br />mallow
<br />thrstle, Canada (14)
<br />Imrdzu (72) 4
<br />]. Diffuse spotted knapweed: Apply from rosette to early flower or to fall
<br />regrowth.. Optimum time is mid-bolt.
<br />2. Marshelder: Apply early seasmn when plants are less than 6 inches.
<br />3. Western ragweed: Usc lowermte when plants are less than4inches.Herbicide
<br />effect is slow.
<br />4. Yellow starthisde: Apply from rosette tumid-bolt.
<br />5. Biennial thistles such as bull and musk thistle: Apply lower rate from rosette
<br />m mid-bolt. Increase rate for applications from mid-bolt to bud.
<br />Powered by C&P Press.
<br />
|