My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
2012-02-28_REVISION - M1980244 (82)
DRMS
>
Day Forward
>
Revision
>
Minerals
>
M1980244
>
2012-02-28_REVISION - M1980244 (82)
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
8/24/2016 4:49:12 PM
Creation date
3/15/2012 3:22:17 PM
Metadata
Fields
Template:
DRMS Permit Index
Permit No
M1980244
IBM Index Class Name
REVISION
Doc Date
2/28/2012
Doc Name
VOL 7, Part 1: Spill Response Plan
From
CC&V
To
DRMS
Type & Sequence
AM10
Email Name
TC1
Media Type
D
Archive
No
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
188
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
with equipment containing oil for ancillary purposes are not required to provide the secondary <br />containment required for bulk storage facilities 0112.8(c))." Based on the preceding regulatory <br />discussion, secondary containment is not required for electrical transformers. However, <br />most of the active (in service) transformers sit on elevated concrete pads. Typically, the <br />transformers are labeled with signs, and are located in highly visible areas. In the unlikely <br />event that a transformer should completely rupture the oil inside could conceivably report <br />to the concrete elevated pads, or the ground surrounding the units. The most likely <br />amount spilled is expected to be less than 10 gallons. <br />4.1.6.5 Spill Countermeasures (Clean -up Procedures) for Electrical Gear <br />Section 3.2 provides the general spill response procedures for use involving spills around electrical <br />gear. The following narrative provides additional detail on spill clean up. <br />Clean -up of Spills Around Electrical Gear <br />Clean up of oil spills can be addressed with sorbent materials (pads, oil dry, "kitty litter ", and /or sand) <br />by placing these materials directly into the spilled pool of oil or grease. Sorbent pads that have been <br />used to remove petroleum products, including antifreeze, greases and oils, can be disposed of as a <br />conventional solid waste and can be placed into the commercial solid waste containers (dumpsters) at <br />various locations around the property, provided no solvents or other potentially hazardous wastes <br />have been added. Sorbent materials that have been saturated with oil but are not dripping can be <br />disposed as conventional solid waste. <br />Leaks or spills of petroleum products during transport or during product transfer will create an oil stain <br />on the ground surface. CC &V's clean -up policy is as follows: If the majority ( >50 %) of the area <br />consisting of 9 square feet (3 feet by 3 feet) is affected (stained), then the affected area will be <br />removed (i.e., the soil and oil mixture) and placed in the blast hole stemming material pile or as <br />directed by the Environmental Resources Department. <br />Free liquids with an oily sheen that are collected during mobile servicing in the field will be pumped or <br />gravity fed into appropriate containers. Oils mixed with water will be hauled to the oil skimmer sump <br />located at the New Truck Shop Wash Bay or shipped off site for recycle. <br />4.1.6.6 Inspections and Tank Integrity Testing for Electrical Gear <br />Monthly visual inspections of electrical transformers will be conducted and documented on the form in <br />Appendix G. Electrical gear will not be subject to the tank integrity testing protocols. <br />4.1.6.7 Conformance with Regulations for Electrical Gear <br />Applicable state and local guidelines are assumed to be the same as the Federal Regulations at 40 <br />CFR Part 112, and therefore, under §112.7(1) the electrical transformer facilities discussed in this <br />section are in conformance with applicable requirements. <br />4.1.7 Diesel Generators at ADR ( "Adsorption Desorption Recovery Plant") <br />Four Caterpillar diesel generator units (3 Model 3516B's and one 3512) provide stand -by power to the <br />ADR in the event of an electrical power outage at the facility. The three larger generator units are <br />constructed with built -in secondary containment tanks (referred to as "rupture tanks "). The capacity of <br />diesel on the larger units is 3000 gallons each. The smaller unit has a 1200- gallon diesel capacity <br />but does not have the secondary containment of the larger units. <br />4.1.7.1 Storage and Use of Diesel at the ADR Generators <br />Diesel fuel is stored in the belly tanks as described above. <br />Spill Response Plan <br />EMS: AGANA/CCV <br />G:1EMS1PIans\Emergency Response Plans\SRP PIan1SRP Plan.doc <br />Printed Copies are Uncontrolled <br />August 17, 2010 <br />Doc. # E -006 <br />Revision 05 <br />26 <br />
The URL can be used to link to this page
Your browser does not support the video tag.