2010-07-27_PERMIT FILE - M2009076 ‎(29)‎

• Permit No: M2009076
• IBM Index Class Name: PERMIT FILE
• Doc Date: 7/27/2010
• Doc Name: Adequacy Response- GCL- Geosynthetic Clay Liner
• From: Venture Resources
• To: DRMS
• Email Name: ACS
• Media Type: D
• Archive: No

F®cae,
• ? coLORADO LINING
?
INTERNATIONAL ??®®
•
•
Product Specifications
GEOCOMPOSITE
Product Data Sheet
TESTED PROPERTY TEST METHOD FREQUENCY MINIMUM AVERAGE ROLL VALUEt'0
Geocomposite 6 oz/yd2 8 oz/yd2 10 oz/ydZ
Product Code F42060060S F42080080S F42100100S
TransmissivityW, gal/min/ft (ml/sec) ASTM D 4716-00 1/540,000 W 0.48 (1 x 101) 0.48 (1 x 104) 0.43 (9 x 10-5)
Ply Adhesion, Ibrn (gfcm) GRI GC-7 1/50,000 ft' 1.0078) 1.0078) 1.0 (178)
Roll Width, ft (m) 14.5 (4.4) 14.5 (4.4) 14.5 (4.4)
Roll Length, ft (m) 230 (70.1) 200 (60.9) 190 (58.0)
Roll Area, ft' (mz) 3,335 (310) 2,900 (269) 2,755 (256)
Geonet core(b)
Transmissivity,"' gal/min/ft (m'/sec) ASTM D 4716-00 9.66 (2 x 10-1) 9.66 (2 x 10-') 9.66 (2 x 10-1)
Thickness, mil (mm) ASTM D 5199 1/50,000 ft2 200(5) 200(5) 200(5)
Density, g/cm' ASTM D 1505 1/50,000 ft' 0.94 0.94 0.94
Tensile Strength (MD), Win (N/mm) ASTM, D 5035 1/50,000 ft- 45(7.9) 45(7.9) 45(7.9)
Carbon Black Content, % ASTM D 1603 1/50,000 ft, 2.0 2.0 2.0
Geotextile (prior to lamination)(1-'
Mass per Unit Area, oz/y& (g/mz) ASTM D 5261 1/90,000 ftz 6(200) 8(270) 10(335)
Grab Tensile, lb (N) ASTM, D 4632 1/90,000 ftz 170 (755) 220 (975) 260 (1,155)
Puncture Strength, lb (N) ASTM, D 4833 1/90,000 ftz 90(395) 120 (525) 165 (725)
AOS, US sieve (mm) ASTM D 4751 1/540,000 ftz 70 (0.212) 80 (0.180) 100 (0.150)
Permittivity, (sec') ASTM D 4491 1/540,000 ftz 1 1 1.5 1.5 1.2
Flow Rate, gpm/ftz (Ipm/mz) ASTM D 4491 1/540,000 ftz 110 (4,480) 110 (4,480) 85 (3,460)
UV Resistance, % retained ASTM D 4355 (after 500 hours) once per formulatio 70 70 70
NOTES:
• ?"Gradient of 0. 1, normal load of 10,000 psf, water at 70° F between steel plates for 15 minutes.
• MComponent properties prior to lamination.
• ")Several geotextiles are available and may be supplied as determined by GSE.
• (`tThese are MARV values that are based on the cumulative results of specimens tested and determined by GSE. AOS in mm is maximum average roll value.
www.coloradolining.com