Laserfiche WebLink
PRODUCT DATA SHEET <br />Description <br />An advanced composite formulated to protect metal surfaces <br />from corrosion and cheri.ical attack It is normally applied at a <br />thickness of 250 microns (10 mils) per coal. Non-shrinking, 100% <br />solids. Colors are Gray and Blue. <br />ARC S7 is a low viscosity high Performance composite lining that <br />is designed to be spray applied but may also be applied by roller <br />or brush. As a one coat system, it functions as a corrosion <br />resistant primer (or many high performance coatings. ARC S7 <br />yields excellent barrier properties for long-tern corrosion and <br />chemical resistance in immersion exposures when used in a <br />multicoat application. The cured ARC S7 provides a high gloss <br />surface with unrivaled adhesion and resistance to corrosion. <br />COMPOSITION -Polymer/ Surface Modified Mineral <br />Composite <br />Matrix - A two component, mode epoxy resin fracture reacted <br />with a polyamidoamine curing agent. <br />Reinforcement-A proprietary blend of surface modified mineral <br />reinforcements designed to provide resistance to permeation, <br />chemical attack and corrosion. <br />Suggested Uses <br />Tanks <br />• Structural Steel <br />gs <br />• Clarifier Tanks <br />Petroleum Storage Tanks <br />Cooling Water Systems <br />Service Water Systems <br />Thickener Tanks <br />Benefits <br />• Dramatically outlasts wnvenlional paints and coatings. <br />• Long pot life allows for ease of use. <br />• 100% solids, no shrinkage on cure. <br />• Outstanding adhesion insures reliable performance againstunder <br />film corrosion. <br />• Able [o be high voltage spark tested for pinhole free films. <br />Packaging <br />Material is available in three sizes: 0,75; 4 and 16 liter kits. <br />Each package contains two pre-measured containers (Part A and <br />Pan B). A mixing tool, brush and instructions for use are <br />enclosed wdh the 0,75 and 4 liter kits. The 16 liter kit contains <br />only application instructions, <br />Coverage <br />Based on a 250 p (10 mils) thickness <br />0,75 liters will cover 3.0 sq. meters (32 sq ft.) <br />4 liters will cover 16 sq. meters (170 sq. ft.) <br />16 liters will cover 64 sq. meters (678 sq. ft.) <br />To calculate the kilograms required for a giver application use the <br />appropriate formula below. <br />1.5 (g/cc) x Area (m')x Average Thickness from} = kg <br />3 5 z Area (ft') x Average Thickness (inches) = kg <br />Chemrca! Resistance <br />Tested at 21 °C (70°F). Samples cured 7 day:: at 25°C (77°F). <br />1 =Continuous long term immersion <br />2 =Short term/intermittent immersion <br />3 =Splash and spills with immediate cleanup, vapors <br />4 =Not recommended for direct contact <br />Acids <br />10% Acetic 4 <br />10%Hydrochtoric 1 <br />20°/ Hydrochloric 2 <br />10% Sulfuric 2 <br />20% Sulfuric 3 <br />5°/ Nitric 3 <br />10%, Nitric 4 <br />10% Phosphoric 3 <br />50°/ Phosphoric 4 <br />Alkalies B Bleaches <br />28% Ammonium Hydroxide 1 <br />10%PotassiumHydroxitle 1 <br />50% Potassium Hydroxitle 2 <br />10%SodiumHytlroxide 1 <br />50% Sodum Hydroxide 2 <br />6%Sodium Hypochlorite 1 <br />10%Hydrogen Peroxide 1 <br />Other Compounds <br />Bunker C 1 <br />Diesel Fuel 1 <br />Isopropyl Alcohol 1 <br />Kerosene 1 <br />Naphtha 1 <br />Salt Water 1 <br />Sewage 1 <br />Toluene 2 <br />Xylene 2 <br />FGec~""hn a'1'~ia"'~a _ a ,'-'~ ~a.,., . ~. .... M.,~SPa ~+~' k` ,, ^'~?' <br />_~ .. <br />Cured Density --------------- 1,5 g/cc 94 Ib/ cu fl. <br />Tensile <br />Flexural Modulus <br />>140 <br />3°r~ <br />420 <br />6000 <br />Heat Deflection Temperature (ASTM D 646) 46°C 115°F <br />Hardness Share D (ASTM D 2240) BS <br />Vertical Sag Resistance ----------------- Nri sag <br />at 21 °C (70°F) and 250 p (10 mils) <br />Maximum Temperature Wet Service 52°C 125°F <br />(Dependent an servicel Drv Service 80'C 175°F <br />' d~RC®S 1 <br />