Laserfiche WebLink
Section 3 - Chemical/Environmental Resistance <br /> Part 1 - XR-5e Fluid Resistance Guidelines <br /> The data below is the result of laboratory tests and is intended to serve only as a guide. No performance warranty is <br /> intended or implied.The degree of chemical attack on any material is governed by the conditions under which it is <br /> exposed. Exposure time,temperature, and size of the area of exposure usually varies considerably in application, <br /> therefore,this table is given and accepted at the user's risk. Confirmation of the validity and suitability in specific <br /> cases should be obtained. Contact a Seaman Corporation Representative for recommendation on specific applications. <br /> When considering XR-5 for specific applications, it is suggested that a sample be tested in actual service before <br /> specification.Where impractical,tests should be devised which simulate actual service conditions as closely as possible. <br /> EXPOSURE RATING EXPOSURE RATING <br /> AFFF A JP-4 Jet Fuel A <br /> Acetic Acid(5%) B JP-5 Jet Fuel A <br /> Acetic Acid (50%) C JP-8 Jet Fuel A <br /> Ammonium Phosphate T Kerosene A <br /> Ammonium Sulfate T Magnesium Chloride T <br /> Antifreeze(Ethylene Glycol) A Magnesium Hydroxide T <br /> Animal Oil A Methanol A <br /> Aqua Regia X Methyl Alcohol A <br /> ASTM Fuel A(100% Iso-Octane) A Methyl Ethyl Ketone X <br /> ASTM Oil#2(Flash Pt. 240°C) A Mineral Spirits A <br /> ASTM Oil#3 A Naphtha A <br /> Benzene X Nitric Acid(5%) B <br /> Calcium Chloride Solutions T Nitric Acid(50%) C <br /> Calcium Hydroxide T Perchloroethylene C <br /> 20% Chlorine Solution A Phenol X <br /> Clorox A Phenol Formaldehyde B <br /> Conc.Ammonium Hydroxide A Phosphoric Acid (50%) A <br /> Corn Oil A Phosphoric Acid (100%) C <br /> Crude Oil A Phthalate Plasticizer C <br /> Diesel Fuel A Potassium Chloride T <br /> Ethanol A Potassium Sulphate T <br /> Ethyl Acetate C Raw Linseed Oil A <br /> Ethyl Alcohol A SAE-30 Oil A <br /> Fertilizer Solution A Salt Water(25%) B <br /> #2 Fuel Oil A Sea Water A <br /> #6 Fuel Oil A Sodium Acetate Solution T <br /> Furfural X Sodium Bisulfite Solution T <br /> Gasoline B Sodium Hydroxide(60%) A <br /> Glycerin A Sodium Phosphate T <br /> Hydraulic Fluid-Petroleum Based A Sulphuric Acid(50%) A <br /> Hydraulic Fluid-Phosphate Tanic Acid(50%) A <br /> Ester Based C Toluene C <br /> Hydrocarbon Type II(40%Aromatic) C Transformer Oil A <br /> Hydrochloric Acid(50%) A Turpentine A <br /> Hydrofluoric Acid(5%) A Urea Formaldehyde A <br /> Hydrofluoric Acid (50%) A UAN A <br /> Hydrofluosilicic Acid (30%) A Vegetable Oil A <br /> Isopropyl Alcohol T Water(200°F) A <br /> Ivory Soap A Xylene X <br /> Jet A A Zinc Chloride T <br /> Ratings are based on visual and physical examination of samples after removal from the test chemical after the samples of Black XR-5 <br /> were immersed for 28 days at room temperature.Results represent ability of material to retain its performance properties when in <br /> contact with the indicated chemical. <br /> Rating Key: <br /> A—Fluid has little or no effect <br /> B—Fluid has minor to moderate effect <br /> C—Fluid has severe effect <br /> T—No data- likely to be acceptable <br /> X—No data -not likely to be acceptable <br /> 9 <br />