2019-04-25_REVISION - M2008080 ‎(7)‎

• Permit No: M2008080
• IBM Index Class Name: Revision
• Doc Date: 4/25/2019
• Doc Name: Adequacy Review Response
• From: J & T Consulting
• To: DRMS
• Type & Sequence: TR4
• Email Name: PSH
• Media Type: D
• Archive: No

Plugging Procedure for Intent and Subsequent Report
CIBP#1: Depth 6808 with 2 sacks cmt on top. CIPB#2: Depth 6466 with 2 sacks cmt on top.
CIBP#3: Depth with sacks cmt on top. CIPB#4: Depth with sacks cmt on top.
CIBP#5: Depth with sacks cmt on top. NOTE:Two(2)sacks cement
required on all CIBPs.
Set 268 sks cmt from 718 ft.to 0 ft. Plug Type: STUB PLUG Plug Tagged:
Set sks cmt from ft.to ft. Plug Type: Plug Tagged: �. .
Set sks cmt from ft.to ft. Plug Type: Plug Tagged: r..
Set sks cmt from ft.to ft. Plug Type: Plug Tagged:
Set sks cmt from ft.to ft. Plug Type: Plug Tagged:
Perforate and squeeze at ft.with sacks. Leave at least 100 ft. in casing CICR Depth
Perforate and squeeze at ft.with sacks. Leave at least 100 ft. in casing CICR Depth
Perforate and squeeze at ft.with sacks. Leave at least 100 ft. in casing CICR Depth
(Cast Iron Cement Retainer Depth)
Set sacks half in. half out surface casing from ft.to ft. Plug Tagged:
Set sacks at surface
Cut four feet below ground level,weld on plate Above Ground Dry-Hole Marker: I Yes No
Set sacks in rat hole Set sacks in mouse hole
Additional Plugging Information for Subsequent Report Only
Casing Recovered: 610 ft. 4+1/2 inch casing Plugging Date: 11/13/2016
of
*Wireline Contractor: Nabors *Cementing Contractor: Bayou
Type of Cement and Additives Used: 15.8 ppg Class G Cement
Flowline/Pipeline has been abandoned per Rule 1105 r Yes iNo *ATTACH JOB SUMMARY
Technical Detail/Comments:
Motis 7A (05-123-20402)/Plugging Procedure
Producing Formation: Codell 6858'-6868'
TD:7054' PBTD: 7009'
Surface Casing: 8 5/8"24#@ 404'w/285 sxs
Production Casing: 4 1/2" 10.5#@ 7034' w/360 sks cmt (TOC 2566' —CBL)
Tubing: 2 3/8"tubing set at 6849'. (5/7/2002)
Procedure:
1. MIRU RU pulling unit. Pull 2 3/8"tubing.
2. RU wireline company.
3.TIH with CIBP. Set CIBP at 6808'.Top with 2 sxs 15.8#/gal Cl G cement.
4.TIH with CIBP.Set CIBP at 6466'.Top with 2 sxs 15.8#/gal Cl G cement.
5.TIH with casing cutter.Cut 4 Y2"casing at 610'. Recover 610'of 4'Y2"casing.
6.TIH with tubing to 718'. Mix and pump 268 sxs of 15.8#/gal Cl G cement down tubing. Cement to surface.
7. Cut surface casing 6' below ground level and weld on cap.
I hereby certify all statements made in this form are,to the best of my knowledge,true,correct,and complete.
Signed: Print Name: Jenifer Hakkarinen
Title: RegTech Date: 12/9/2016 Email: [e-mail]
Date Run:411512019 Doc[#401164413]Well Name:MOTIS 7A Page 2 of 3