2018-04-23_REVISION - M2007031 ‎(4)‎

• Permit No: M2007031
• IBM Index Class Name: Revision
• Doc Date: 4/23/2018
• Doc Name Note: Response to Deficiencies
• Doc Name: Response to Deficiencies
• From: The Turquoise Connection, Inc.
• To: DRMS
• Type & Sequence: AM1
• Email Name: ERR
• Media Type: D
• Archive: No

30 foot area
A ( B ( c 0 ( E ( F 1_ G H
1 RECLAMATION BOND CALCULATION SPREADSHEET
2 Revised 12/4/2010 1 I i
3 NOTE: USE THIS SPREADSHEET ONLY IF YOUR TOTAL DISTURBANCE IS LESS THAN 20 ACRES AND AN AQUIFER
4 PROTECTION PERMIT IS NOT REQUIRED.
5
6Jl SER INPUT AND RECLAMATION COST TOTAL
7 Please fill in the yellow cells relating to the areas to be disturbed during the operation.
8 Use the units indicated-feet(ft),square feet(sf),inches(in),cubic yards(cu yd),etc.
9 Identify structure construction type by placing an X in the . ••'ate cell.
10 Leave boxes that do not apply to your operation blank.
11
122 Roads _ #1 L= a (ft) Width(ft) I
13 (average lengths and widths) #2 Length(ft) Width(ft)
14 #3 Length(ft) Width(ft)
15
18 Road cuts #1 Length(ft) Width(ft) Depth of cut(ft)
17 (ave.length,width and depth #2 Length(ft) Width(ft) Depth of cut(ft)
18 of cut at hi.hwall #3 L, ., ft Width ft D-•, of cut ft
19 111111111
20
21 Cleared areas #1 Length(ft) 30 90
22 (average lengths&widths) #2 Length(ftj-
23 #3 Len.th ft -
za n paoe., -
25
26 Drill pads #1 Length(ft) - Depth of cut(ft)
27 (average lengths,widths and #2 Length(ft) Width(ft) Depth of cut(ft)
28 de. of cut #3 L:, .. ft Width(ft) D:•, of cut ft
29
30
31 Culverts #1 Length(ft) Diameter(ft) u '�
32 (average lengths,diameter #2 Len. ft IIIMME Diameter(ft) IIIIMI Ave.der ft
33 and depth of burial) #3 L, .. ft MEM Diameter(ft)
34
35 Waste dumps/spoil piles #1 Length(ft) Width(ft) Face height(ft)
38 (average lengths,widths and #2 Length(ft) Width(ft) Face height(ft)
37 height of top surfaces of dump) #3 Length(ft) Width(ft) Face height(ft)
38 #4 Length(ft) Width(ft) Face height(ft)
39 #5 Length(ft) Width(ft) Face height(ft)
40 #6 Length(ft) Width(ft) Face height(ft)
41 #7 Le .. ft Width ft Face hei.ht ft
42 #8 Lena ft - i i T)
43 #9 L= e h ft -=='- Facehei.ht ft
44 #10 Len.h ft -MEIMM'- Face hei.ht ft
45 ---
46 Shafts #1 Length(ft) Width(ft) Depth(ft) _
47 (lengths and widths of shafts I . of water ft MOM
48 at collar) #2 L= . ft MIMI Width(ft) I I Depth(ft)
49 De. of wet, ft -
50 ii #3 Length(ft) - Width(ft) I Depth(ft)
51 Depth of water(ft)11111=111
52
ater(ft)-
52 #4 Length(ft) Width(ft) Depth(ft)
53 Depth of water(ft)-
54 #5 Length(ft) ili Width(ft) I Depth(ft)
55 'Depth of water(ft)-
56 MEM
57 Dista%e to source of HC fill Miles _
58
59 Pits I #1 Length(ft) Width(ft) Depth(ft)
60 (average lengths and widths #2 Length U _ Width(ft) Depth(ft)
61 at surface) #3 Length(ft) - Widthffi) Depth(ft)
62 #4 Length(ft) Width(ft) _ Depth(ft)
63 #5 Length(ft) Width(ft) - Depth(ft)
64 #6 • Length(ft) Width(ft) Depth(ft)
65 #7 Length(ft) Width(ft) Depth(ft)
66 #8 Length(ft) Width(ft) Depth(ft)
67 #9 Length(ft) Width(ft) Depth(ft)
68 #10 Length(ft) Width(ft) Depth(ft)
69
70 INghwalls #1 Length(ft) Height(ft) Blasting required?
71 (average length and height) #2 Length(ft) Height(ft) (Yes or No)
72 #3 Length(ft) Height(ft)
73 #4 Length(ft) - Height(ft)
74
75 Trenches #1 Length(ft) 30 Width(ft) 100 Depth(ft) 2
76 (average lengths and widths #2 Length(ft) 8 Width(ft) 10 -Depth(ft) 4
77 at surface) #3 Length(ft) Width(ft) Depth(ft)
78 #4 Length(ft) Width(ft)- Depth(ft)
79 #5 Length(ft) Width(ft) Depth(ft)
80 #6 Length(ft) Width(ft) Depth(ft)
81 #7 Length(ft) _ Width(ft) Depth(ft)
82 #8 Length(ft) Width(ft) Depth(ft)
83 #9 Length(ft) Width(ft) Depth(ft)