2018-04-23_REVISION - M2007031 ‎(4)‎

• Permit No: M2007031
• IBM Index Class Name: Revision
• Doc Date: 4/23/2018
• Doc Name Note: Response to Deficiencies
• Doc Name: Response to Deficiencies
• From: The Turquoise Connection, Inc.
• To: DRMS
• Type & Sequence: AM1
• Email Name: ERR
• Media Type: D
• Archive: No

Scott Blue II
A I B ( C D E F G H
1 RECLAMATION BOND CALCULATION SPREADSHEET
2 Revised 12/4/2010
3 NOTE: USE THIS SPREADSHEET ONLY IF YOUR TOTAL DISTURBANCE IS LESS THAN 20 ACRES MR AN AQUIFER
4 PROTECTION PERMIT IS NOT REQUIRED.
5 r I
6 SER INPUT AND RECLAMATION COST TOT
7 Please fill in the yellow cells relating to the areas to be disturbed during the operation.
8,Use the units indicated-feet(ft),square feet(sf),inches(in),cubic yards(cu yd),etc.
9 Identify structure construction type by placing an X in the appropriate cell.
10 Leave boxes that do not apply to your operation blank.
11
12 Roads #1 Length(ft) Width(ft) -
13 (average lengths and widths) #2 Length(ft) Width(!)__ killEMIIIP
14 - #3 Length(ft) Width(ft)
15
16 Road cuts #1 Length(ft) Width(ft) Depth of cut(ft)
17 (ave.length,width and depth #2 Length(ft) Width ft iii.„; :. Depth of cut(ft)
18 of cut at hi hwall #3 Len h ft Width ft '_ Depth of cut(ft)
19
20
21 Cleared areas #1 Length(ft) 200 Width(ft) 300
22 (average lengths&widths) #2 Length(ft) Width(ft)
23 #3 Length(ftp Width(ft)
24
25
26 Drill pads #1 Length(ft) ` Width(ft) Depth of cut(ft)
27 (average lengths,widths end #2 Length(ft) Width(ft) Depth of cut(ft)
28 depth of cut #3 L ft Width(ft) Depth of cut(ft)
29
30
31 Culverts #1 Length(ft) Diameter(ft) Ave.depth(ft)
32 (average lengths,diameter #2 Length(ft) Diameter(ft) Ave.depth(ft)
33 and depth of burial) #3 Length(ft) Diameter(ft) Ave.depth(ft)
34
35 Waste dumps/spoil piles #1 Length(ft) 60 Width(ft) 50 Face height(ft) 20
36 (average lengths,,widths and #2 Length(ft) Width(ft) Face height(ft)
37 height of top surfaces of dump) #3 Length(ft) Width(It) - Face height(ft)
38 _ #4 Length(ft) Width(ft) Face height(ft)
39 #5 Length(ft) Width(ft) Face height(ft)
40 #6 Length(ft) Width(ft) Face height(ft)
41 #7 Length(ft)- Width(ft) Face height(ft)
42 #8 Length(ft) Width(ft) Face height(ft)
43 #9 Length(ft) Width(ft) Face height(ft) i
44 __ #10 Length(ft) Width(ft) _ Face height(ft)
45
46 Shafts #1 Length(ft) Width(ft) I Depth(ft) 1
47 (lengths and widths of shafts Depth of water(ft)
48 at collar) #2 Length(ft) Width(ft) I I Depth(ft)
49 Depth of water(it)
50 #3 Length1ft) Width(ft) I I Depth(ft)
51 Depth of water(ft)
52 #4 Length(ft) Width(ft) I I Depth(ft)
53 Depth of water(ft)
54 #5 ' Length(ft) Width(ft) I I Depth(ft)
55 Depth of water(ft)
56
t...... ------Miles
58
59 Pits #1 Length(ft) Width(ft) Depth(ft)
60 (average lengths and widths #2 Length(ft) Width(ft) Depth(ft)
61 at surface) #3 Length(ft) Width(ft) Depth(ft)
62 #4 Length(ft) Width(ft) Depth(ft)
63 #5 Length(ft) Width(ft) Depth(ft) _
64 #6 Length(ft) Width(ft) Depth(ft)
65 #7 Length(ft) Width(ft) Depth(ft)
66 #8 Length(ft) Width(f) Depth(ft)
67 #9 Length(ft) _Width(ft) Depth(ft)
68 #10 Length(ft) Width(ft) Depth(ft)
69
70 Highwalis #1 Length(ft) Height(ft) Blasting required?
71 (average length and height) #2 Length(ft) Height(ft) (Yes or No)___
72 #3 Length(ft) _ Height(ft) 1
73 #4 Length(ff) Height(ft)
74
75 Trenches #1 Length(ft) 80 Width(ft) 30 Depth(ft) 2
76 (average lengths and widths #2 Length(ft) _ 100 Width(ft) 20 Depth(ft) 8
77 at surface) #3 Length(ft)_ Width(ft) Depth(ft)
78 #4 Length(ft) Width(ft) Depth(ft)
79 #5 Length(ft) Width(ft) __ Depth(ft)
80 #6 Length(ft)_ Width(ft) Depth(ft)
81 #7 Length(ft)_ Width(ft) - Depth(ft)
g— #8 Length(ft) Width(ft) Depth(ft)
83 #9 Length(ft) Width(ft) Depth(ft)