Laserfiche WebLink
03 39 23 MEMBRANECONCRETE <br /> Maxcure Wax White <br /> Water-Emulsion, (J Wax-Based Curin( CompoundComound <br /> �NEEREO CONCRETE PROWGCS <br /> DESCRIPTION PHYSICAL PROPERTIES <br /> Maxcure Wax White is a water-emulsion,VOC compliant, Complies with VOC contents in accordance with Federal EPA <br /> white pigmented,dissipating wax,concrete curing compound. 40 CFR Part 59 Table 1,Subpart D for Concrete Curing and <br /> Maxcure Wax White has been formulated to form a membrane Sealing. <br /> film on the surface of the concrete optimizing water retention VOC 0 g/L <br /> for maximum concrete hydration and compressive strength Color Milky White <br /> development. The white pigment increases reflectance,cooling Viscosity 80 CPS <br /> the freshly poured concrete. Reflectance reduces surface tem- Flash Point Non-Flammable <br /> perature,thus minimizing vapor pressure and moisture loss. Dry Time 1 hr C?70°F(21°C) <br /> USES Shelf Life 1 Year <br /> Maxcure Wax White is ideal for curing concrete that will be STORAGE <br /> exposed to the sun,such as bridge decks,piers,highways, Protect from freezing. Store material in an interior,cool,dry <br /> pavement slabs,airport runways,parking decks,sidewalks, place above 45°F(7°C). Shelf life is one year in original,un- <br /> ramps,curbs and gutters. opened container. <br /> BENEFITS CLEAN-UP <br /> • Contributes to LEED EQ Credit 4.2 Clean tools and equipment with warm,soapy water. After <br /> • Water-Based: Low odor material has dried,it may be necessary to use solvents such as <br /> • VOC Compliant: Meets stringent requirements mineral spirits,toluene or xylene. <br /> • Clean-up with water <br /> • Approved by many state DOTS LIMITATIONS <br /> • Minimizes thermal cracking,dusting and defects In addition to the limitations already mentioned,please note <br /> • Performance: Produces hard,dense concrete the following. If surface is to receive subsequent coatings, <br /> • Strength: Increases compressive and tensile strength over paints or toppings,it is necessary to completely remove the <br /> untreated concrete curing compound. Maxcure Wax White must be exposed <br /> • Will not permanently discolor colored concrete to heat,traffic or sunlight to fully dissipate. When applied <br /> • Consistent: Strict Quality Control testing and standards indoors,chemical means may be necessary for removal. Do not <br /> STANDARDS apply when the temperature of concrete is below 40°F(4°C). Do <br /> not mix with any other products. Do not pour unused material <br /> Maxcure Wax White meets and exceeds the requirements of back into original container. <br /> ASTM C309 Type 2,Class A and AASHTO M148 as tested in <br /> accordance with ASTM C156 and AASHTO T155. <br /> SURFACE PREPARATION <br /> Maxcure Wax White should be applied to freshly placed con- <br /> crete as soon as the bleed(surface)water has dissipated. On <br /> formed and vertical surfaces,Maxcure Wax White should be <br /> applied to concrete immediately upon removal of the form- <br /> work. <br /> COVERAGE <br /> Approximately 200 ftz/gal. Coverage may vary depending on <br /> porosity of surface. <br /> MIXING <br /> For best results,mix thoroughly before each use. Do not over <br /> agitate or use high speed mixing equipment. <br /> PLACING <br /> Apply with a low pressure sprayer,brush or roller at a rate of <br /> 200 ft2/gal. Spray application is recommended. A hand held <br /> pump sprayer or an airless industrial sprayer is acceptable. <br /> Apply evenly without puddling. Do not interchange use of <br /> sprayer that has been used to spray a solvent based product. <br /> Packaging: 5 gal(18.9 Q pail,55 gal(207.9 Q drum <br />