Laserfiche WebLink
GEOTEX 104F is a woven monofilament polypropylene geotextile produced by Propex, and will <br />meet the following Minimum Average Roll Values (MARV) when tested in accordance with the <br />methods listed below. The individual filaments are woven into a regular network and calendared <br />such that filaments retain dimensional stability relative to each other. These characteristics <br />make GEOTEX 104F ideal for filtration beneath hard armor systems. The geotextile is resistant <br />to ultraviolet degradation and to biological and chemical environments normally found in soils. <br />GEOTEX 104F conforms to the property values listed below.' Propex performs internal <br />Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic <br />Accreditation Institute - Laboratory Accreditation Program (GAI -LAP). This product is NTPEP <br />approved for AASHTO standards. <br />MARV2 <br />PROPERTY TEST METHOD ENGLISH METRIC <br />ORIGIN OF MATERIALS <br />% U.S. Manufactured Inputs <br />100% <br />100% <br />% U.S. Manufactured <br />100% <br />100% <br />MECHANICAL <br />Tensile Strength (Grab) <br />ASTM D -4632 <br />370 x 250 Ibs <br />1,647 x 1113 N <br />Elongation <br />ASTM D -4632 <br />15 x 15% <br />15 x 15% <br />CBR Puncture <br />ASTM D -6241 <br />950 Ibs <br />4228 N <br />Trapezoidal Tear <br />ASTM D -4533 <br />100 x 60 Ibs <br />445 x 267 N <br />ENDURANCE <br />UV Resistance ASTM D -4355 90% 90% <br />% Retained at 500 hrs <br />HYDRAULIC <br />Apparent Opening Size (AOS)3 <br />ASTM D -4751 <br />70 US Std. Sieve <br />0.212 mm <br />Percent Open Area <br />CW -02215 MOD.4 <br />4-6% <br />4-6% <br />Permittivity <br />ASTM D -4491 <br />0.28 sec -1 <br />0.28 sec-1 <br />Water Flow Rate <br />ASTM D -4491 <br />18 m ft2 <br />733 I m m2 <br />ROLL SIZES 6 ft x 300 ft 1.83 m x 91.5 m <br />12ftx300ft 3.66mx91.5m <br />NOTES: <br />1. The property values listed above are effective 04/2011 and are subject to change without notice. <br />2 Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus <br />two standard deviations. Statistically, it yields a 97.7% degree of confidence that any samples taken from quality <br />assurance testing will exceed the value reported. <br />3 Maximum average roll value. <br />4. Army Corp of Engineers test method correlated to light emitted through fabric. (Area of Openings/Total Area X 100 %) <br />Propex "1G::utt.yllio <br />TESTED PROVEN.TRUSTED. <br />www.geotextile.com <br />Propex Operating Company, LLC • 6025 Lee Highway, Suite 425 • PO Box 22788 • Chattanooga, TN 37422 <br />ph 423 899 0444 • ph 800 621 1273 • fax 423 899 7619 <br />Geotee, Landloko, Pyramato, X3®, SuperGr , Petromafo and Petrotac are registered trademarks of Propex Operating Company, LLC <br />This publcation should not be construed as engmsenng advice While information contained in this publication is accurate to the best of our knowledge, Propex does notwamant its accuracy or completeness The ultimate customer and user of the products should <br />assume sale responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such other <br />written warranty as may be agreed by Propex and individual customers Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability ar fitness for a particular purpose, or ansing from provision of <br />samples, a course of dealing or usage of trade <br />0 2011 Propex Operating Company, LLC <br />