Laserfiche WebLink
TYPICAL PROPERTIES -TABLE 2.01 -B <br />Notes: <br />1 LLDPE refers to Linear Low Density Polyethylene and VLDPE refers to Very Low Density Polyethylene. <br />2 First value represents lowest individual value. Second value represents minimum average roll value. <br />3 Core Thickness, exclusive of textured surface. <br />4 Seam strength refers to both fusion and extruded seams for LLDPE to LLDPE welds. <br />s If peel strength exceeds ultimate tensile strength of the sheet but the sample fails FTB, the test will be considered a <br />pass. <br />6 Federal Test Method Standards. <br />7 Film Tear Bond (FTB) is defined as failure of one of the sheets by tearing, instead of separating from the other <br />sheet at the weld interface area (sheet fails before weld). <br />Section 02776 <br />Geomembrane <br />C: AMEC_CC &V\Phase 5 VLF\PSSA Cert Report\Appendices\Appendix E \SPECS \02776.r1.doc <br />Page 11 of 22 <br />September 3, 2008 <br />Revision 1 <br />Smooth <br />Textured <br />Property <br />Test Method <br />100 mil LLDPE <br />100 mil LLDPE <br />Thickness (mils)2 <br />GRI -GM8 <br />90 (min)/ 100 (min) <br />90 (min)/ 100 (min)3 <br />Compound Density (g/cc) <br />ASTM D 1505 <br />0.939 (max) <br />0.939 (max) <br />Carbon Black Dispersion <br />ASTM D3015 <br />Al, A2, A3 <br />A1, A2, A3 <br />Carbon Black Content ( %) <br />ASTM D 1603 <br />2 -3 <br />2 -3 <br />Tensile Properties <br />1. Ultimate Tensile Strength (ppi) <br />ASTM D 638, NSF 54 <br />380 (min) <br />180 (min) <br />2. Ultimate Elongation ( %)(2.5" gauge) <br />ASTM D 638, NSF 54 <br />480 (min) <br />300 (min) <br />Puncture Resistance (lbs.) <br />ASTM D 4833 <br />150 (min) <br />130 (min) <br />Field Seam Properties4 <br />1. Shear Strength (ppi) <br />6 <br />2. Peel Strength (Inside and outside <br />ASTM D4437 (modified NSF 54) <br />130 (min) <br />130 (min) <br />tracks for fusion welds) <br />ASTM D4437 (modified NSF 54) <br />110 (min), FTB1'6'' <br />100 (min), FTBs'6'7 <br />Notes: <br />1 LLDPE refers to Linear Low Density Polyethylene and VLDPE refers to Very Low Density Polyethylene. <br />2 First value represents lowest individual value. Second value represents minimum average roll value. <br />3 Core Thickness, exclusive of textured surface. <br />4 Seam strength refers to both fusion and extruded seams for LLDPE to LLDPE welds. <br />s If peel strength exceeds ultimate tensile strength of the sheet but the sample fails FTB, the test will be considered a <br />pass. <br />6 Federal Test Method Standards. <br />7 Film Tear Bond (FTB) is defined as failure of one of the sheets by tearing, instead of separating from the other <br />sheet at the weld interface area (sheet fails before weld). <br />Section 02776 <br />Geomembrane <br />C: AMEC_CC &V\Phase 5 VLF\PSSA Cert Report\Appendices\Appendix E \SPECS \02776.r1.doc <br />Page 11 of 22 <br />September 3, 2008 <br />Revision 1 <br />